Welcome to Automatic Appliance Parts, Inc.

Asko Clothes Dryer
Display	Condition	Remedy
F1	Condensate drain overfilling	Check condensate reservoir pump and drain tube.
F2	Maximum drying time exceeded (3 hours)	Check for tripped circuit breaker or blown fuse Check ductwork for lint build-up Check hi-limit and cycling thermostat Check heating element
F3	Thermistor fault	Open thermistor, replace Bad wiring to thermistor
F4	Too much lint in the lint filter, front housing, or in the condenser	Clean lint from lint filter and/or condenser
F5	Fault in the moisture sensor	Lint covering sensor in front of housing Bad sensor Bad wiring to sensor

Kitchen Aid Front Loading Gas and Electric Dryer Fault (Models KGHS01PMT/WH and KEHS01PMT/WH)
Display	Condition	Remedy
PF	Power failure	"PF" flashes to indicate that a power failure occurred while the dryer was running. Press HOLD TO START to continue the cycle, or press OFF/Pause to clear the display.
E1	Thermistor open	Replace thermistor if found defective
E2	Thermistor shorted	Replace thermistor if found defective
E3	User interface or software mismatch	This error code will ONLY appear when in the Diagnostic Test mode. If the E3 error code is displayed, there is a user interface or software mismatch. It is also possible that a component on the console electronics or the electronic control board has failed. Replace defective component.

Kitchen Aid Front Loading Gas and Electric Dryer Fault (Models KHEV01RSS and KHGV01RSS)
Display	Condition	Remedy
PF	Power failure	"PF" flashes to indicate that a power failure occurred while the dryer was running. Press START to continue the cycle, or press Pause/Cancel to clear the display.
E1	Temperature sensor open	E1 flashes in the numeric display when the temperature sensing circuit is open. Replace temperature sensor if faulty.
E2	Temperature sensor shorted	E2 flashes in the numeric display when the temperature sensing circuit is shorted. Replace temperature sensor if faulty.
E3	Blower rotation failure	If during a cycle the blower rotational speed drops below 500 rpms, all outputs will be turned off and error code E3 will be displayed.
E4	Tumbler rotation failure	If during a cycle the tumbler rotational speed drops to 0, all outputs will be turned off and error code E4 will be displayed.
E5	Dry rack sensor	If during a Dry Rack cycle the signal is lost, all outputs are turned off and E5 is displayed.
E6	Exhaust high limit fault	If the exhaust temperature goes above 87.7C (190F) all outputs will turn off and E6 will be displayed.

Maytag *Stackable A/W and Dryer Fault Codes*
Display	Condition	Remedy
"L" persists in washer display	Lid lock failure	Replace switch, linkage, lock solenoid or control board.
1E persists in washer display	Lid lock failure	Replace lid lock switch or control board.
9E appears in dryer display	Door switch failure	Check door switch wiring or door switch or control board
"U"	Unbalanced load	Unbalance switch or control board
6E appears in dryer display	Temp control error	Ambient (room) temperature too cool, -or- thermistor wire harness control board
7E appears in dryer display	Temp control error - overheating	Check: venting for restriction thermistor control board cycling thermostat (regular)
8E appears in dryer display	Motor relay circuit	Check: relay coil wire harness or control board

SEARS/KENMORE
Range/Stove/Ovens

Sears contracts with many different manufacturers to build all of their appliances. Use the chart below to
determine which manufacturer actually built your range or oven. After you determine which brand
appliance you have, refer to the chart for that manufacturer to look up an error code.

The first 3 digits of the model number specify the manufacturer
Roper	Whirlpool	Caloric	Kelvinator	Gibson	D & M	Amana	WCI
103 647 835 911 155	106 110 562 665 198	174 960	417 662 628	253	587	596	790
GE	Speed Queen	Maytag	Litton	Toshiba	Fedders	Tappan	Jenn Air
363 362	651	925	747	562	484	791	629

Whirlpool Calypso Clothes Dryer
Display	Condition	Remedy
PF	Power Failure	If the household power goes off and the control board was in RUN mode or PAUSE mode, the electronic control board will display a power failure error code.
E1 or E2	Thermistor Failure	The dryer will not operate if the exhaust temperature drops below 18 F, or exceeds 250 F. When the thermistor circuit is open (>50K ohms), the error code E1 flashes in the display. When the thermistor circuit is shorted (<500 ohms), the error code E2 flashes in the display. Normal thermistor resistance values: 60 degrees F. - 15.3K ohms. 70 degrees F. - 11.9K ohms. 80 degrees F. - 9.2K ohms.
E3	Touchpad or Software mismatch	Flashes when there is a touchpad or software mismatch. NOTE: This error code is displayed only in diagnostics mode.

Whirlpool Duet Front Loading Gas and Electric Clothes Dryer Fault Codes
Display	Condition	Remedy
PF	Power Failure	"PF" flashes to indicate that a power failure occurred while the dryer was running. Press HOLD TO START to continue the cycle, or press OFF/Pause to clear the display.
E1	Thermistor Open	Replace thermistor
E2	Thermistor Shorted	Replace thermistor